CVE Database

In the Linux kernel, the following vulnerability has been resolved: coresight: cti: Fix hang in cti_disable_hw() cti_enable_hw() and cti_disable_hw() are called from an atomic context so shouldn't use runtime PM because it can result in a sleep when communicating with firmware. Since commit 3c6656337852 ("Revert "firmware: arm_scmi: Add clock management to the SCMI power domain""), this causes a hang on Juno when running the Perf Coresight tests or running this command: perf record -e cs_etm//u -- ls This was also missed until the revert commit because pm_runtime_put() was called with the wrong device until commit 692c9a499b28 ("coresight: cti: Correct the parameter for pm_runtime_put") With lock and scheduler debugging enabled the following is output: coresight cti_sys0: cti_enable_hw -- dev:cti_sys0 parent: 20020000.cti BUG: sleeping function called from invalid context at drivers/base/power/runtime.c:1151 in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 330, name: perf-exec preempt_count: 2, expected: 0 RCU nest depth: 0, expected: 0 INFO: lockdep is turned off. irq event stamp: 0 hardirqs last enabled at (0): [<0000000000000000>] 0x0 hardirqs last disabled at (0): [<ffff80000822b394>] copy_process+0xa0c/0x1948 softirqs last enabled at (0): [<ffff80000822b394>] copy_process+0xa0c/0x1948 softirqs last disabled at (0): [<0000000000000000>] 0x0 CPU: 3 PID: 330 Comm: perf-exec Not tainted 6.0.0-00053-g042116d99298 #7 Hardware name: ARM LTD ARM Juno Development Platform/ARM Juno Development Platform, BIOS EDK II Sep 13 2022 Call trace: dump_backtrace+0x134/0x140 show_stack+0x20/0x58 dump_stack_lvl+0x8c/0xb8 dump_stack+0x18/0x34 __might_resched+0x180/0x228 __might_sleep+0x50/0x88 __pm_runtime_resume+0xac/0xb0 cti_enable+0x44/0x120 coresight_control_assoc_ectdev+0xc0/0x150 coresight_enable_path+0xb4/0x288 etm_event_start+0x138/0x170 etm_event_add+0x48/0x70 event_sched_in.isra.122+0xb4/0x280 merge_sched_in+0x1fc/0x3d0 visit_groups_merge.constprop.137+0x16c/0x4b0 ctx_sched_in+0x114/0x1f0 perf_event_sched_in+0x60/0x90 ctx_resched+0x68/0xb0 perf_event_exec+0x138/0x508 begin_new_exec+0x52c/0xd40 load_elf_binary+0x6b8/0x17d0 bprm_execve+0x360/0x7f8 do_execveat_common.isra.47+0x218/0x238 __arm64_sys_execve+0x48/0x60 invoke_syscall+0x4c/0x110 el0_svc_common.constprop.4+0xfc/0x120 do_el0_svc+0x34/0xc0 el0_svc+0x40/0x98 el0t_64_sync_handler+0x98/0xc0 el0t_64_sync+0x170/0x174 Fix the issue by removing the runtime PM calls completely. They are not needed here because it must have already been done when building the path for a trace. [ Fix build warnings ]

In the Linux kernel, the following vulnerability has been resolved: drm/mipi-dsi: Detach devices when removing the host Whenever the MIPI-DSI host is unregistered, the code of mipi_dsi_host_unregister() loops over every device currently found on that bus and will unregister it. However, it doesn't detach it from the bus first, which leads to all kind of resource leaks if the host wants to perform some clean up whenever a device is detached.

In the Linux kernel, the following vulnerability has been resolved: net: ethernet: ti: Fix return type of netcp_ndo_start_xmit() With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG), indirect call targets are validated against the expected function pointer prototype to make sure the call target is valid to help mitigate ROP attacks. If they are not identical, there is a failure at run time, which manifests as either a kernel panic or thread getting killed. A proposed warning in clang aims to catch these at compile time, which reveals: drivers/net/ethernet/ti/netcp_core.c:1944:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict] .ndo_start_xmit = netcp_ndo_start_xmit, ^~~~~~~~~~~~~~~~~~~~ 1 error generated. ->ndo_start_xmit() in 'struct net_device_ops' expects a return type of 'netdev_tx_t', not 'int'. Adjust the return type of netcp_ndo_start_xmit() to match the prototype's to resolve the warning and CFI failure.

In the Linux kernel, the following vulnerability has been resolved: ext4: add EXT4_IGET_BAD flag to prevent unexpected bad inode There are many places that will get unhappy (and crash) when ext4_iget() returns a bad inode. However, if iget the boot loader inode, allows a bad inode to be returned, because the inode may not be initialized. This mechanism can be used to bypass some checks and cause panic. To solve this problem, we add a special iget flag EXT4_IGET_BAD. Only with this flag we'd be returning bad inode from ext4_iget(), otherwise we always return the error code if the inode is bad inode.(suggested by Jan Kara)

In the Linux kernel, the following vulnerability has been resolved: ALSA: usb-audio: Fix potential memory leaks When the driver hits -ENOMEM at allocating a URB or a buffer, it aborts and goes to the error path that releases the all previously allocated resources. However, when -ENOMEM hits at the middle of the sync EP URB allocation loop, the partially allocated URBs might be left without released, because ep->nurbs is still zero at that point. Fix it by setting ep->nurbs at first, so that the error handler loops over the full URB list.

In the Linux kernel, the following vulnerability has been resolved: iommu/vt-d: Clean up si_domain in the init_dmars() error path A splat from kmem_cache_destroy() was seen with a kernel prior to commit ee2653bbe89d ("iommu/vt-d: Remove domain and devinfo mempool") when there was a failure in init_dmars(), because the iommu_domain cache still had objects. While the mempool code is now gone, there still is a leak of the si_domain memory if init_dmars() fails. So clean up si_domain in the init_dmars() error path.

In the Linux kernel, the following vulnerability has been resolved: cxl: fix possible null-ptr-deref in cxl_guest_init_afu|adapter() If device_register() fails in cxl_register_afu|adapter(), the device is not added, device_unregister() can not be called in the error path, otherwise it will cause a null-ptr-deref because of removing not added device. As comment of device_register() says, it should use put_device() to give up the reference in the error path. So split device_unregister() into device_del() and put_device(), then goes to put dev when register fails.

In the Linux kernel, the following vulnerability has been resolved: memory: pl353-smc: Fix refcount leak bug in pl353_smc_probe() The break of for_each_available_child_of_node() needs a corresponding of_node_put() when the reference 'child' is not used anymore. Here we do not need to call of_node_put() in fail path as '!match' means no break. While the of_platform_device_create() will created a new reference by 'child' but it has considered the refcounting.

In the Linux kernel, the following vulnerability has been resolved: drm/amd: fix potential memory leak This patch fix potential memory leak (clk_src) when function run into last return NULL. s/free/kfree/ - Alex

In the Linux kernel, the following vulnerability has been resolved: rtc: class: Fix potential memleak in devm_rtc_allocate_device() devm_rtc_allocate_device() will alloc a rtc_device first, and then run dev_set_name(). If dev_set_name() failed, the rtc_device will memleak. Move devm_add_action_or_reset() in front of dev_set_name() to prevent memleak. unreferenced object 0xffff888110a53000 (size 2048): comm "python3", pid 470, jiffies 4296078308 (age 58.882s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 08 30 a5 10 81 88 ff ff .........0...... 08 30 a5 10 81 88 ff ff 00 00 00 00 00 00 00 00 .0.............. backtrace: [<000000004aac0364>] kmalloc_trace+0x21/0x110 [<000000000ff02202>] devm_rtc_allocate_device+0xd4/0x400 [<000000001bdf5639>] devm_rtc_device_register+0x1a/0x80 [<00000000351bf81c>] rx4581_probe+0xdd/0x110 [rtc_rx4581] [<00000000f0eba0ae>] spi_probe+0xde/0x130 [<00000000bff89ee8>] really_probe+0x175/0x3f0 [<00000000128e8d84>] __driver_probe_device+0xe6/0x170 [<00000000ee5bf913>] device_driver_attach+0x32/0x80 [<00000000f3f28f92>] bind_store+0x10b/0x1a0 [<000000009ff812d8>] drv_attr_store+0x49/0x70 [<000000008139c323>] sysfs_kf_write+0x8d/0xb0 [<00000000b6146e01>] kernfs_fop_write_iter+0x214/0x2d0 [<00000000ecbe3895>] vfs_write+0x61a/0x7d0 [<00000000aa2196ea>] ksys_write+0xc8/0x190 [<0000000046a600f5>] do_syscall_64+0x37/0x90 [<00000000541a336f>] entry_SYSCALL_64_after_hwframe+0x63/0xcd

In the Linux kernel, the following vulnerability has been resolved: ntb_netdev: Use dev_kfree_skb_any() in interrupt context TX/RX callback handlers (ntb_netdev_tx_handler(), ntb_netdev_rx_handler()) can be called in interrupt context via the DMA framework when the respective DMA operations have completed. As such, any calls by these routines to free skb's, should use the interrupt context safe dev_kfree_skb_any() function. Previously, these callback handlers would call the interrupt unsafe version of dev_kfree_skb(). This has not presented an issue on Intel IOAT DMA engines as that driver utilizes tasklets rather than a hard interrupt handler, like the AMD PTDMA DMA driver. On AMD systems, a kernel WARNING message is encountered, which is being issued from skb_release_head_state() due to in_hardirq() being true. Besides the user visible WARNING from the kernel, the other symptom of this bug was that TCP/IP performance across the ntb_netdev interface was very poor, i.e. approximately an order of magnitude below what was expected. With the repair to use dev_kfree_skb_any(), kernel WARNINGs from skb_release_head_state() ceased and TCP/IP performance, as measured by iperf, was on par with expected results, approximately 20 Gb/s on AMD Milan based server. Note that this performance is comparable with Intel based servers.

In the Linux kernel, the following vulnerability has been resolved: RDMA/core: Make sure "ib_port" is valid when access sysfs node The "ib_port" structure must be set before adding the sysfs kobject, and reset after removing it, otherwise it may crash when accessing the sysfs node: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000050 Mem abort info: ESR = 0x96000006 Exception class = DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 Data abort info: ISV = 0, ISS = 0x00000006 CM = 0, WnR = 0 user pgtable: 4k pages, 48-bit VAs, pgdp = 00000000e85f5ba5 [0000000000000050] pgd=0000000848fd9003, pud=000000085b387003, pmd=0000000000000000 Internal error: Oops: 96000006 [#2] PREEMPT SMP Modules linked in: ib_umad(O) mlx5_ib(O) nfnetlink_cttimeout(E) nfnetlink(E) act_gact(E) cls_flower(E) sch_ingress(E) openvswitch(E) nsh(E) nf_nat_ipv6(E) nf_nat_ipv4(E) nf_conncount(E) nf_nat(E) nf_conntrack(E) nf_defrag_ipv6(E) nf_defrag_ipv4(E) mst_pciconf(O) ipmi_devintf(E) ipmi_msghandler(E) ipmb_dev_int(OE) mlx5_core(O) mlxfw(O) mlxdevm(O) auxiliary(O) ib_uverbs(O) ib_core(O) mlx_compat(O) psample(E) sbsa_gwdt(E) uio_pdrv_genirq(E) uio(E) mlxbf_pmc(OE) mlxbf_gige(OE) mlxbf_tmfifo(OE) gpio_mlxbf2(OE) pwr_mlxbf(OE) mlx_trio(OE) i2c_mlxbf(OE) mlx_bootctl(OE) bluefield_edac(OE) knem(O) ip_tables(E) ipv6(E) crc_ccitt(E) [last unloaded: mst_pci] Process grep (pid: 3372, stack limit = 0x0000000022055c92) CPU: 5 PID: 3372 Comm: grep Tainted: G D OE 4.19.161-mlnx.47.gadcd9e3 #1 Hardware name: https://www.mellanox.com BlueField SoC/BlueField SoC, BIOS BlueField:3.9.2-15-ga2403ab Sep 8 2022 pstate: 40000005 (nZcv daif -PAN -UAO) pc : hw_stat_port_show+0x4c/0x80 [ib_core] lr : port_attr_show+0x40/0x58 [ib_core] sp : ffff000029f43b50 x29: ffff000029f43b50 x28: 0000000019375000 x27: ffff8007b821a540 x26: ffff000029f43e30 x25: 0000000000008000 x24: ffff000000eaa958 x23: 0000000000001000 x22: ffff8007a4ce3000 x21: ffff8007baff8000 x20: ffff8007b9066ac0 x19: ffff8007bae97578 x18: 0000000000000000 x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000 x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000 x11: 0000000000000000 x10: 0000000000000000 x9 : 0000000000000000 x8 : ffff8007a4ce4000 x7 : 0000000000000000 x6 : 000000000000003f x5 : ffff000000e6a280 x4 : ffff8007a4ce3000 x3 : 0000000000000000 x2 : aaaaaaaaaaaaaaab x1 : ffff8007b9066a10 x0 : ffff8007baff8000 Call trace: hw_stat_port_show+0x4c/0x80 [ib_core] port_attr_show+0x40/0x58 [ib_core] sysfs_kf_seq_show+0x8c/0x150 kernfs_seq_show+0x44/0x50 seq_read+0x1b4/0x45c kernfs_fop_read+0x148/0x1d8 __vfs_read+0x58/0x180 vfs_read+0x94/0x154 ksys_read+0x68/0xd8 __arm64_sys_read+0x28/0x34 el0_svc_common+0x88/0x18c el0_svc_handler+0x78/0x94 el0_svc+0x8/0xe8 Code: f2955562 aa1603e4 aa1503e0 f9405683 (f9402861)

In the Linux kernel, the following vulnerability has been resolved: macintosh: fix possible memory leak in macio_add_one_device() Afer commit 1fa5ae857bb1 ("driver core: get rid of struct device's bus_id string array"), the name of device is allocated dynamically. It needs to be freed when of_device_register() fails. Call put_device() to give up the reference that's taken in device_initialize(), so that it can be freed in kobject_cleanup() when the refcount hits 0. macio device is freed in macio_release_dev(), so the kfree() can be removed.

In the Linux kernel, the following vulnerability has been resolved: cpufreq: Init completion before kobject_init_and_add() In cpufreq_policy_alloc(), it will call uninitialed completion in cpufreq_sysfs_release() when kobject_init_and_add() fails. And that will cause a crash such as the following page fault in complete: BUG: unable to handle page fault for address: fffffffffffffff8 [..] RIP: 0010:complete+0x98/0x1f0 [..] Call Trace: kobject_put+0x1be/0x4c0 cpufreq_online.cold+0xee/0x1fd cpufreq_add_dev+0x183/0x1e0 subsys_interface_register+0x3f5/0x4e0 cpufreq_register_driver+0x3b7/0x670 acpi_cpufreq_init+0x56c/0x1000 [acpi_cpufreq] do_one_initcall+0x13d/0x780 do_init_module+0x1c3/0x630 load_module+0x6e67/0x73b0 __do_sys_finit_module+0x181/0x240 do_syscall_64+0x35/0x80 entry_SYSCALL_64_after_hwframe+0x63/0xcd

In the Linux kernel, the following vulnerability has been resolved: xen/gntdev: Accommodate VMA splitting Prior to this commit, the gntdev driver code did not handle the following scenario correctly with paravirtualized (PV) Xen domains: * User process sets up a gntdev mapping composed of two grant mappings (i.e., two pages shared by another Xen domain). * User process munmap()s one of the pages. * User process munmap()s the remaining page. * User process exits. In the scenario above, the user process would cause the kernel to log the following messages in dmesg for the first munmap(), and the second munmap() call would result in similar log messages: BUG: Bad page map in process doublemap.test pte:... pmd:... page:0000000057c97bff refcount:1 mapcount:-1 \ mapping:0000000000000000 index:0x0 pfn:... ... page dumped because: bad pte ... file:gntdev fault:0x0 mmap:gntdev_mmap [xen_gntdev] readpage:0x0 ... Call Trace: <TASK> dump_stack_lvl+0x46/0x5e print_bad_pte.cold+0x66/0xb6 unmap_page_range+0x7e5/0xdc0 unmap_vmas+0x78/0xf0 unmap_region+0xa8/0x110 __do_munmap+0x1ea/0x4e0 __vm_munmap+0x75/0x120 __x64_sys_munmap+0x28/0x40 do_syscall_64+0x38/0x90 entry_SYSCALL_64_after_hwframe+0x61/0xcb ... For each munmap() call, the Xen hypervisor (if built with CONFIG_DEBUG) would print out the following and trigger a general protection fault in the affected Xen PV domain: (XEN) d0v... Attempt to implicitly unmap d0's grant PTE ... (XEN) d0v... Attempt to implicitly unmap d0's grant PTE ... As of this writing, gntdev_grant_map structure's vma field (referred to as map->vma below) is mainly used for checking the start and end addresses of mappings. However, with split VMAs, these may change, and there could be more than one VMA associated with a gntdev mapping. Hence, remove the use of map->vma and rely on map->pages_vm_start for the original start address and on (map->count << PAGE_SHIFT) for the original mapping size. Let the invalidate() and find_special_page() hooks use these. Also, given that there can be multiple VMAs associated with a gntdev mapping, move the "mmu_interval_notifier_remove(&map->notifier)" call to the end of gntdev_put_map, so that the MMU notifier is only removed after the closing of the last remaining VMA. Finally, use an atomic to prevent inadvertent gntdev mapping re-use, instead of using the map->live_grants atomic counter and/or the map->vma pointer (the latter of which is now removed). This prevents the userspace from mmap()'ing (with MAP_FIXED) a gntdev mapping over the same address range as a previously set up gntdev mapping. This scenario can be summarized with the following call-trace, which was valid prior to this commit: mmap gntdev_mmap mmap (repeat mmap with MAP_FIXED over the same address range) gntdev_invalidate unmap_grant_pages (sets 'being_removed' entries to true) gnttab_unmap_refs_async unmap_single_vma gntdev_mmap (maps the shared pages again) munmap gntdev_invalidate unmap_grant_pages (no-op because 'being_removed' entries are true) unmap_single_vma (For PV domains, Xen reports that a granted page is being unmapped and triggers a general protection fault in the affected domain, if Xen was built with CONFIG_DEBUG) The fix for this last scenario could be worth its own commit, but we opted for a single commit, because removing the gntdev_grant_map structure's vma field requires guarding the entry to gntdev_mmap(), and the live_grants atomic counter is not sufficient on its own to prevent the mmap() over a pre-existing mapping.

In the Linux kernel, the following vulnerability has been resolved: cgroup: split cgroup_destroy_wq into 3 workqueues A hung task can occur during [1] LTP cgroup testing when repeatedly mounting/unmounting perf_event and net_prio controllers with systemd.unified_cgroup_hierarchy=1. The hang manifests in cgroup_lock_and_drain_offline() during root destruction. Related case: cgroup_fj_function_perf_event cgroup_fj_function.sh perf_event cgroup_fj_function_net_prio cgroup_fj_function.sh net_prio Call Trace: cgroup_lock_and_drain_offline+0x14c/0x1e8 cgroup_destroy_root+0x3c/0x2c0 css_free_rwork_fn+0x248/0x338 process_one_work+0x16c/0x3b8 worker_thread+0x22c/0x3b0 kthread+0xec/0x100 ret_from_fork+0x10/0x20 Root Cause: CPU0 CPU1 mount perf_event umount net_prio cgroup1_get_tree cgroup_kill_sb rebind_subsystems // root destruction enqueues // cgroup_destroy_wq // kill all perf_event css // one perf_event css A is dying // css A offline enqueues cgroup_destroy_wq // root destruction will be executed first css_free_rwork_fn cgroup_destroy_root cgroup_lock_and_drain_offline // some perf descendants are dying // cgroup_destroy_wq max_active = 1 // waiting for css A to die Problem scenario: 1. CPU0 mounts perf_event (rebind_subsystems) 2. CPU1 unmounts net_prio (cgroup_kill_sb), queuing root destruction work 3. A dying perf_event CSS gets queued for offline after root destruction 4. Root destruction waits for offline completion, but offline work is blocked behind root destruction in cgroup_destroy_wq (max_active=1) Solution: Split cgroup_destroy_wq into three dedicated workqueues: cgroup_offline_wq – Handles CSS offline operations cgroup_release_wq – Manages resource release cgroup_free_wq – Performs final memory deallocation This separation eliminates blocking in the CSS free path while waiting for offline operations to complete. [1] https://github.com/linux-test-project/ltp/blob/master/runtest/controllers

In the Linux kernel, the following vulnerability has been resolved: net/tcp: Fix a NULL pointer dereference when using TCP-AO with TCP_REPAIR A NULL pointer dereference can occur in tcp_ao_finish_connect() during a connect() system call on a socket with a TCP-AO key added and TCP_REPAIR enabled. The function is called with skb being NULL and attempts to dereference it on tcp_hdr(skb)->seq without a prior skb validation. Fix this by checking if skb is NULL before dereferencing it. The commentary is taken from bpf_skops_established(), which is also called in the same flow. Unlike the function being patched, bpf_skops_established() validates the skb before dereferencing it. int main(void){ struct sockaddr_in sockaddr; struct tcp_ao_add tcp_ao; int sk; int one = 1; memset(&sockaddr,'\0',sizeof(sockaddr)); memset(&tcp_ao,'\0',sizeof(tcp_ao)); sk = socket(AF_INET, SOCK_STREAM, IPPROTO_TCP); sockaddr.sin_family = AF_INET; memcpy(tcp_ao.alg_name,"cmac(aes128)",12); memcpy(tcp_ao.key,"ABCDEFGHABCDEFGH",16); tcp_ao.keylen = 16; memcpy(&tcp_ao.addr,&sockaddr,sizeof(sockaddr)); setsockopt(sk, IPPROTO_TCP, TCP_AO_ADD_KEY, &tcp_ao, sizeof(tcp_ao)); setsockopt(sk, IPPROTO_TCP, TCP_REPAIR, &one, sizeof(one)); sockaddr.sin_family = AF_INET; sockaddr.sin_port = htobe16(123); inet_aton("127.0.0.1", &sockaddr.sin_addr); connect(sk,(struct sockaddr *)&sockaddr,sizeof(sockaddr)); return 0; } $ gcc tcp-ao-nullptr.c -o tcp-ao-nullptr -Wall $ unshare -Urn BUG: kernel NULL pointer dereference, address: 00000000000000b6 PGD 1f648d067 P4D 1f648d067 PUD 1982e8067 PMD 0 Oops: Oops: 0000 [#1] SMP NOPTI Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 11/12/2020 RIP: 0010:tcp_ao_finish_connect (net/ipv4/tcp_ao.c:1182)

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Harden uplink netdev access against device unbind The function mlx5_uplink_netdev_get() gets the uplink netdevice pointer from mdev->mlx5e_res.uplink_netdev. However, the netdevice can be removed and its pointer cleared when unbound from the mlx5_core.eth driver. This results in a NULL pointer, causing a kernel panic. BUG: unable to handle page fault for address: 0000000000001300 at RIP: 0010:mlx5e_vport_rep_load+0x22a/0x270 [mlx5_core] Call Trace: <TASK> mlx5_esw_offloads_rep_load+0x68/0xe0 [mlx5_core] esw_offloads_enable+0x593/0x910 [mlx5_core] mlx5_eswitch_enable_locked+0x341/0x420 [mlx5_core] mlx5_devlink_eswitch_mode_set+0x17e/0x3a0 [mlx5_core] devlink_nl_eswitch_set_doit+0x60/0xd0 genl_family_rcv_msg_doit+0xe0/0x130 genl_rcv_msg+0x183/0x290 netlink_rcv_skb+0x4b/0xf0 genl_rcv+0x24/0x40 netlink_unicast+0x255/0x380 netlink_sendmsg+0x1f3/0x420 __sock_sendmsg+0x38/0x60 __sys_sendto+0x119/0x180 do_syscall_64+0x53/0x1d0 entry_SYSCALL_64_after_hwframe+0x4b/0x53 Ensure the pointer is valid before use by checking it for NULL. If it is valid, immediately call netdev_hold() to take a reference, and preventing the netdevice from being freed while it is in use.

In the Linux kernel, the following vulnerability has been resolved: dm-stripe: fix a possible integer overflow There's a possible integer overflow in stripe_io_hints if we have too large chunk size. Test if the overflow happened, and if it did, don't set limits->io_min and limits->io_opt;

In the Linux kernel, the following vulnerability has been resolved: ASoC: qcom: q6apm-lpass-dais: Fix NULL pointer dereference if source graph failed If earlier opening of source graph fails (e.g. ADSP rejects due to incorrect audioreach topology), the graph is closed and "dai_data->graph[dai->id]" is assigned NULL. Preparing the DAI for sink graph continues though and next call to q6apm_lpass_dai_prepare() receives dai_data->graph[dai->id]=NULL leading to NULL pointer exception: qcom-apm gprsvc:service:2:1: Error (1) Processing 0x01001002 cmd qcom-apm gprsvc:service:2:1: DSP returned error[1001002] 1 q6apm-lpass-dais 30000000.remoteproc:glink-edge:gpr:service@1:bedais: fail to start APM port 78 q6apm-lpass-dais 30000000.remoteproc:glink-edge:gpr:service@1:bedais: ASoC: error at snd_soc_pcm_dai_prepare on TX_CODEC_DMA_TX_3: -22 Unable to handle kernel NULL pointer dereference at virtual address 00000000000000a8 ... Call trace: q6apm_graph_media_format_pcm+0x48/0x120 (P) q6apm_lpass_dai_prepare+0x110/0x1b4 snd_soc_pcm_dai_prepare+0x74/0x108 __soc_pcm_prepare+0x44/0x160 dpcm_be_dai_prepare+0x124/0x1c0

In the Linux kernel, the following vulnerability has been resolved: net: rfkill: gpio: Fix crash due to dereferencering uninitialized pointer Since commit 7d5e9737efda ("net: rfkill: gpio: get the name and type from device property") rfkill_find_type() gets called with the possibly uninitialized "const char *type_name;" local variable. On x86 systems when rfkill-gpio binds to a "BCM4752" or "LNV4752" acpi_device, the rfkill->type is set based on the ACPI acpi_device_id: rfkill->type = (unsigned)id->driver_data; and there is no "type" property so device_property_read_string() will fail and leave type_name uninitialized, leading to a potential crash. rfkill_find_type() does accept a NULL pointer, fix the potential crash by initializing type_name to NULL. Note likely sofar this has not been caught because: 1. Not many x86 machines actually have a "BCM4752"/"LNV4752" acpi_device 2. The stack happened to contain NULL where type_name is stored

In the Linux kernel, the following vulnerability has been resolved: crypto: ccp - Always pass in an error pointer to __sev_platform_shutdown_locked() When 9770b428b1a2 ("crypto: ccp - Move dev_info/err messages for SEV/SNP init and shutdown") moved the error messages dumping so that they don't need to be issued by the callers, it missed the case where __sev_firmware_shutdown() calls __sev_platform_shutdown_locked() with a NULL argument which leads to a NULL ptr deref on the shutdown path, during suspend to disk: #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: Oops: 0000 [#1] SMP NOPTI CPU: 0 UID: 0 PID: 983 Comm: hib.sh Not tainted 6.17.0-rc4+ #1 PREEMPT(voluntary) Hardware name: Supermicro Super Server/H12SSL-i, BIOS 2.5 09/08/2022 RIP: 0010:__sev_platform_shutdown_locked.cold+0x0/0x21 [ccp] That rIP is: 00000000000006fd <__sev_platform_shutdown_locked.cold>: 6fd: 8b 13 mov (%rbx),%edx 6ff: 48 8b 7d 00 mov 0x0(%rbp),%rdi 703: 89 c1 mov %eax,%ecx Code: 74 05 31 ff 41 89 3f 49 8b 3e 89 ea 48 c7 c6 a0 8e 54 a0 41 bf 92 ff ff ff e8 e5 2e 09 e1 c6 05 2a d4 38 00 01 e9 26 af ff ff <8b> 13 48 8b 7d 00 89 c1 48 c7 c6 18 90 54 a0 89 44 24 04 e8 c1 2e RSP: 0018:ffffc90005467d00 EFLAGS: 00010282 RAX: 00000000ffffff92 RBX: 0000000000000000 RCX: 0000000000000000 ^^^^^^^^^^^^^^^^ and %rbx is nice and clean. Call Trace: <TASK> __sev_firmware_shutdown.isra.0 sev_dev_destroy psp_dev_destroy sp_destroy pci_device_shutdown device_shutdown kernel_power_off hibernate.cold state_store kernfs_fop_write_iter vfs_write ksys_write do_syscall_64 entry_SYSCALL_64_after_hwframe Pass in a pointer to the function-local error var in the caller. With that addressed, suspending the ccp shows the error properly at least: ccp 0000:47:00.1: sev command 0x2 timed out, disabling PSP ccp 0000:47:00.1: SEV: failed to SHUTDOWN error 0x0, rc -110 SEV-SNP: Leaking PFN range 0x146800-0x146a00 SEV-SNP: PFN 0x146800 unassigned, dumping non-zero entries in 2M PFN region: [0x146800 - 0x146a00] ... ccp 0000:47:00.1: SEV-SNP firmware shutdown failed, rc -16, error 0x0 ACPI: PM: Preparing to enter system sleep state S5 kvm: exiting hardware virtualization reboot: Power down Btw, this driver is crying to be cleaned up to pass in a proper I/O struct which can be used to store information between the different functions, otherwise stuff like that will happen in the future again.

In the Linux kernel, the following vulnerability has been resolved: drm: bridge: anx7625: Fix NULL pointer dereference with early IRQ If the interrupt occurs before resource initialization is complete, the interrupt handler/worker may access uninitialized data such as the I2C tcpc_client device, potentially leading to NULL pointer dereference.

The Trinity Audio – Text to Speech AI audio player to convert content into audio plugin for WordPress is vulnerable to Reflected Cross-Site Scripting via the 'range-date' parameter in all versions up to, and including, 5.20.2 due to insufficient input sanitization and output escaping. This makes it possible for unauthenticated attackers to inject arbitrary web scripts in pages that execute if they can successfully trick a user into performing an action such as clicking on a link.

The Trinity Audio – Text to Speech AI audio player to convert content into audio plugin for WordPress is vulnerable to Cross-Site Request Forgery in all versions up to, and including, 5.20.2. This is due to missing or incorrect nonce validation in the '/admin/inc/post-management.php' file. This makes it possible for unauthenticated attackers to activate/deactivate posts via a forged request granted they can trick a site administrator into performing an action such as clicking on a link.

The Contest Gallery – Upload, Vote & Sell with PayPal and Stripe plugin for WordPress is vulnerable to Stored Cross-Site Scripting via multiple form field parameters in all versions up to, and including, 27.0.2. This is due to insufficient input sanitization and output escaping on user-supplied attributes. This makes it possible for authenticated attackers, with author-level access or higher, to inject arbitrary web scripts in pages that will execute whenever a user accesses an injected page.

The Majestic Before After Image plugin for WordPress is vulnerable to Stored Cross-Site Scripting via the 'before_label' and 'after_label' parameters in versions less than, or equal to, 2.0.1 due to insufficient input sanitization and output escaping. This makes it possible for authenticated attackers, with contributor-level access and above, to inject arbitrary web scripts in pages that will execute whenever a user accesses an injected page.

The WDesignKit – Elementor & Gutenberg Starter Templates, Patterns, Cloud Workspace & Widget Builder plugin for WordPress is vulnerable to missing authorization via the wdkit_handle_review_submission function in versions less than, or equal to, 1.2.16. This is due to the plugin not properly verifying that a user is authorized to perform an action. This makes it possible for unauthenticated attackers to submit feedback data to external services.

The WP Photo Album Plus plugin for WordPress is vulnerable to Cross-Site Scripting in all versions up to, and including, 9.0.11.006 due to insufficient input sanitization and output escaping in the wppa_user_upload function. This makes it possible for authenticated attackers, with Subscriber-level access and above, to inject arbitrary web scripts in the photo album descriptions that execute in a victim's browser.

In fetchmail before 6.5.6, the SMTP client can crash when authenticating upon receiving a 334 status code in a malformed context.